Search found 43 matches
- Sat Nov 18, 2023 6:17 pm
- Forum: HARDWARE DISCUSSIONS
- Topic: Falcon Restoration Project
- Replies: 92
- Views: 7655
Re: Falcon Restoration Project
...Also, the cartridge port doesn't seem to work. It boots to the desktop whether the diagnostic cartridge is inserted or not... Check 0.5A fuse. Thanks. It's good. The cartridge actually started working after a while. Possibly the C29 and C30 caps warming up. I've ordered replacements for those an...
- Sat Nov 18, 2023 6:14 pm
- Forum: HARDWARE DISCUSSIONS
- Topic: Falcon Restoration Project
- Replies: 92
- Views: 7655
Re: Falcon Restoration Project
Indeed. I was beginning to think it was a lost cause.
- Sat Nov 18, 2023 4:39 pm
- Forum: HARDWARE DISCUSSIONS
- Topic: Falcon Restoration Project
- Replies: 92
- Views: 7655
- Sat Nov 18, 2023 4:26 pm
- Forum: HARDWARE DISCUSSIONS
- Topic: Falcon Restoration Project
- Replies: 92
- Views: 7655
Re: Falcon Restoration Project
More progress: I fitted all of the remaining missing parts and I was able to get the Falcon to boot! However, just powering up results in a blank display - I have to reset at least once before the boot sequence works. I'm not sure what to think of that. Maybe the auto reset circuit is faulty? Any su...
- Mon Nov 13, 2023 7:50 pm
- Forum: HARDWARE DISCUSSIONS
- Topic: Falcon Restoration Project
- Replies: 92
- Views: 7655
- Mon Nov 13, 2023 4:47 pm
- Forum: HARDWARE DISCUSSIONS
- Topic: Falcon Restoration Project
- Replies: 92
- Views: 7655
Re: Falcon Restoration Project
Well, without a clock nothing will happen, guaranteed. I agree. Have you checked for a clock signal on the CPU at all? a diagnostic cart won't mean a thing if the CPU has no clock signal. Check the basics first. stephen_usher and rubber_jonnie , thanks. Yes, I had checked the clock signal to the CP...
- Mon Nov 13, 2023 2:35 pm
- Forum: HARDWARE DISCUSSIONS
- Topic: Falcon Restoration Project
- Replies: 92
- Views: 7655
Re: Falcon Restoration Project
That's definitely good news. You've got basically basic RGB output from Videl. The most common state with black screens is getting "out of sync" on monitor and bye. Perhaps ROM and/or RAM is not getting its chance to do something further. You could try the diagnostic cartridge + serial ou...
- Sat Nov 11, 2023 1:41 am
- Forum: HARDWARE DISCUSSIONS
- Topic: Falcon Restoration Project
- Replies: 92
- Views: 7655
Re: Falcon Restoration Project
Yes, very happy about the progress. Thanks to everyone for the advice and help!
- Fri Nov 10, 2023 6:25 pm
- Forum: HARDWARE DISCUSSIONS
- Topic: Falcon Restoration Project
- Replies: 92
- Views: 7655
Re: Falcon Restoration Project
Just wire over it, or replace with a low value resistor like 22R,33R,47R values. Thanks. I wired over it and I get video, but just black. No Atari logo, etc. The signal is 15.7Khz H, and 50.1Hz V, 712x242, which seems correct. So, progress. I'm going to probe the bus to see what's happening there.
- Fri Nov 10, 2023 4:46 pm
- Forum: HARDWARE DISCUSSIONS
- Topic: Falcon Restoration Project
- Replies: 92
- Views: 7655
Re: Falcon Restoration Project
Well, no clock = bad juju, so definitely a good place to start :) Also, no clock == no nothing. So far, all of the address lines I tested are high, but yes, L102 is missing. I probed on the oscillator side and it's coming out 32MHz, so I'll either bridge it as suggested or get a replacement. The I ...