Fitting of a 34 pin standard FDD socket to an Atari ST

Update your old 720k to a 1.44 drive etc.
User avatar
rubber_jonnie
Site Admin
Site Admin
Posts: 10389
Joined: Thu Aug 17, 2017 7:40 pm
Location: Essex
Contact:

Fitting of a 34 pin standard FDD socket to an Atari ST

Post by rubber_jonnie »

Hello all

Having been getting along well with the a number of upgrades to my STE, I was constantly finding that the floppy connector/cable was a pain, flapping around as I moved the mainboard to and fro.

So I decided to go ahead and replace the fitted IDC connector with a socket and cable from a standard PC.

Here's an old PC mainboard, ready for removal of FDD socket, the white one in the foreground. Tools used were a temperature controlled soldering iron, liquid flux, 1.5mm solder wick, small forceps, small side cutters, large illuminated magnifier and bravery! Don't worry, the PC was dead :o
donor.jpg
donor.jpg (274.89 KiB) Viewed 10005 times

First I prised the plastic part of the socket off carefully to avoid damage.
donor2.jpg
donor2.jpg (151.72 KiB) Viewed 10005 times

With the plastic part removed, I was ready to remove the pins, now easily visible.
donor3.jpg
donor3.jpg (215.27 KiB) Viewed 10005 times

Using the soldering iron at about 360 degrees C I heated each pin until it could be pulled out with the forceps.Half the pins are out in this shot.
donor4.jpg
donor4.jpg (244.8 KiB) Viewed 10005 times

With all of the pins in a small receptacle for safe keeping, plug a foppy cable into the pin less socket. Now push the pins in from the bottom until they stop in the plug, leaving just about 3 or 4 mm proud, that will push into the STE mainboard. Remove the plug from the socket when done.
socket.jpg
socket.jpg (134.83 KiB) Viewed 10005 times

The fully reassembled socket. You could probably buy one online, I chose this method as I had a sacrificial PC.
socketready.jpg
socketready.jpg (64.17 KiB) Viewed 10005 times

To remove the top clip on the ST FDD plug, push a small screwdriver into the end and lever. Do this at both ends. Don't worry if it breaks, you won't need it again!
clipoff.jpg
clipoff.jpg (301.13 KiB) Viewed 10005 times

Heres the top clip removed.
clipoff2.jpg
clipoff2.jpg (341.54 KiB) Viewed 10005 times

Now simply peel off the old cable.
peel.jpg
peel.jpg (360.37 KiB) Viewed 10005 times

Ready to remove. Start activating bravery here!!
ready.jpg
ready.jpg (374.07 KiB) Viewed 10005 times

I also marked the end where the stripe was for reference, but in a normal ST, the stripe will be towards the front. Bravery to level 2.
mark.jpg
mark.jpg (373.59 KiB) Viewed 10005 times

Bravery should now be at level 3. TAKE YOUR TIME ON THIS PART. Using side cutters, clip away as much of the plastic as you can. Be VERY careful to not damage the tracks on the mainboard. I'd suggest putting a layer or two of tape around the old socket to protect the board. Slowly and carefully chip the plastic away using the side cutters. As each pin is revealed, use the soldering iron to heat it until the pin becomes loose, and using the forceps (Or small pliers if you prefer), pull it from the board. If you encounter any resistance, stop, it is essential you don't damage the vias. Allow to cool, then reheat to avoid too much heat in one spot, and try again. For me, this was more difficult than removing the PLCC socket for the booster!!
remove.jpg
remove.jpg (141.35 KiB) Viewed 10005 times

Once completed, I used solder wick dipped in flux to desolder the holes. I was halfway done desoldering at this point.
desoldering.jpg
desoldering.jpg (155.84 KiB) Viewed 10005 times

With the holes cleared, I checked to ensure there were no solder bridges as a result of the desoldering, and inserted the socket with the keyway facing towards the right of the STE. Check all the pins protrude about 1-1.5mm on the reverse side and solder in place. Bravery can now be set to normal levels.
fitted.jpg
fitted.jpg (135.72 KiB) Viewed 10005 times

Lastly, I took the floppy cable, also from the old PC, and cut it to remove the 5 1/4" drive connector, and the connector the other side of the twist.
cable.jpg
cable.jpg (237.75 KiB) Viewed 10005 times

The cable after cutting. This left me with two 3 1/2" connectors on an untwisted 8" length of ribbon cable. One connector had a key, one did not. The cable I used is to the left.
cable1.jpg
cable1.jpg (246.16 KiB) Viewed 10005 times

Here we can see the keyless connector. The red wire represents pin 1, which we marked earlier. In the background is the socket awaiting the cable.
nearlythere.jpg
nearlythere.jpg (206.68 KiB) Viewed 10005 times

Cable plugged in, red wire to the front of the machine. Because this connector is keyless, it is reversible if you intend to fit a 1.44Mb floppy mod and need to twist the cable.
done.jpg
done.jpg (323.05 KiB) Viewed 10005 times

In case for any reason in the future there's any problem with the images, here's the original facebook post:

https://www.facebook.com/photo.php?fbid ... =3&theater

I hope this is of use to all those of you out there are looking for mods to enhance your ST/STe.

If you do decide to attempt this, don't rush, as the connector is a sod to remove. I've done this successfully, and I hope you will too, but as with any complex task on 20+ year old PCBs, there is always the risk of damage, so attempt at your own risk.
Collector of many retro things!
800XL and 65XE both with Ultimate1MB,VBXL/XE & PokeyMax, SIDE3, SDrive Max, 2x 1010 cassette, 2x 1050 one with Happy mod, 3x 2600 Jr, 7800 and Lynx II
Approx 20 STs, including a 520 STM, 520 STFMs, 3x Mega ST, MSTE & 2x 32 Mhz boosted STEs
Plus the rest, totalling around 50 machines including a QL, 3x BBC Model B, Electron, Spectrums, ZX81 etc...
User avatar
Maeke
Posts: 260
Joined: Thu Aug 17, 2017 3:09 pm

Re: Fitting of a 34 pin standard FDD socket to an Atari ST

Post by Maeke »

Did it too in order to install a selectable dual A drive (floppy/gotek HxC).
Attachments
P1000652.JPG
P1000652.JPG (3.56 MiB) Viewed 10040 times
If i take too long to reply, sorry my cat is sleeping on my laps.
User avatar
IngoQ
Site Admin
Site Admin
Posts: 1064
Joined: Tue Aug 22, 2017 8:38 am
Location: Germany

Re: Fitting of a 34 pin standard FDD socket to an Atari ST

Post by IngoQ »

Wow great how-to, thanks a lot for posting!

I guess I know have no excuse to not do this in order to fix my broken connector :)
Ingo :geek:

| Atari 1040STE@32MHz | Amiga 1200 (ACA1220) | Atari 800XL (U1MB, SIDE2) | Atari 130XL (Sophia DVI) | C64 (1541 Ultimate II, Rev3 RFMod Replacement) | TI 99/4A (F18A, 32k, FlashROM 99) | Sinclair ZX Spectrum 128 (Stereo, DivMMC) | Amstrad CPC664 (512k, M4 Wifi) | ... |
User avatar
DrF
Posts: 640
Joined: Thu Aug 17, 2017 1:18 pm

Re: Fitting of a 34 pin standard FDD socket to an Atari ST

Post by DrF »

rubber_jonnie wrote: Sun Aug 27, 2017 11:27 am Don't worry, the PC was dead :o
Don't think many here would mourn the lost ;)

That is a pretty good idea and guide :)
User avatar
IngoQ
Site Admin
Site Admin
Posts: 1064
Joined: Tue Aug 22, 2017 8:38 am
Location: Germany

Re: Fitting of a 34 pin standard FDD socket to an Atari ST

Post by IngoQ »

DrF wrote: Sun Aug 27, 2017 3:36 pm Don't think many here would mourn the lost ;)
Try to find a PC board with a real floppy controller and start mourning... :-P
Ingo :geek:

| Atari 1040STE@32MHz | Amiga 1200 (ACA1220) | Atari 800XL (U1MB, SIDE2) | Atari 130XL (Sophia DVI) | C64 (1541 Ultimate II, Rev3 RFMod Replacement) | TI 99/4A (F18A, 32k, FlashROM 99) | Sinclair ZX Spectrum 128 (Stereo, DivMMC) | Amstrad CPC664 (512k, M4 Wifi) | ... |
User avatar
DrF
Posts: 640
Joined: Thu Aug 17, 2017 1:18 pm

Re: Fitting of a 34 pin standard FDD socket to an Atari ST

Post by DrF »

IngoQ wrote: Sun Aug 27, 2017 3:48 pm
DrF wrote: Sun Aug 27, 2017 3:36 pm Don't think many here would mourn the lost ;)
Try to find a PC board with a real floppy controller and start mourning... :-P
You know that's a good point :lol:
My last upgrade I was looking for a PC with serial and parallel ports and they had vanished too, not even available on headers just gone :(
User avatar
Maeke
Posts: 260
Joined: Thu Aug 17, 2017 3:09 pm

Re: Fitting of a 34 pin standard FDD socket to an Atari ST

Post by Maeke »

That's why i prefere to assemble my pcs myself, this way they have only what i want and all that i want.
PS you can find those controllers on daughter boards, even the floppy one, which btw is really hard to find.
If i take too long to reply, sorry my cat is sleeping on my laps.
User avatar
rubber_jonnie
Site Admin
Site Admin
Posts: 10389
Joined: Thu Aug 17, 2017 7:40 pm
Location: Essex
Contact:

Re: Fitting of a 34 pin standard FDD socket to an Atari ST

Post by rubber_jonnie »

Cool, glad this has been so warmly received, I hope it helps you all :D
Collector of many retro things!
800XL and 65XE both with Ultimate1MB,VBXL/XE & PokeyMax, SIDE3, SDrive Max, 2x 1010 cassette, 2x 1050 one with Happy mod, 3x 2600 Jr, 7800 and Lynx II
Approx 20 STs, including a 520 STM, 520 STFMs, 3x Mega ST, MSTE & 2x 32 Mhz boosted STEs
Plus the rest, totalling around 50 machines including a QL, 3x BBC Model B, Electron, Spectrums, ZX81 etc...
User avatar
tfhh
Posts: 24
Joined: Sat Aug 26, 2017 5:31 pm
Location: Germany

Re: Fitting of a 34 pin standard FDD socket to an Atari ST

Post by tfhh »

Hi,
rubber_jonnie wrote: Sun Aug 27, 2017 11:27 am So I decided to go ahead and replace the fitted IDC connector with a socket and cable from a standard PC.
That´s one of the first things I ever do in any Atari ST/STE with floppy inside :)

Just for the records... why are you re-use the one from the PC mainboard? These connectors are easily to find normally. Or I didn´t see the goal...

Jurgen
User avatar
Maeke
Posts: 260
Joined: Thu Aug 17, 2017 3:09 pm

Re: Fitting of a 34 pin standard FDD socket to an Atari ST

Post by Maeke »

I do see the goal personally:
1)-the challenge.
2)-having the fdd socket for free.
3)-Destroying an already dead pc motherboard.
If i take too long to reply, sorry my cat is sleeping on my laps.
Post Reply

Return to “FLOPPY DRIVES KITS & UPGRADES”