exxos blog - random goings on

[exxos]

Built up 2 of these, driving me mad

The only way it will work at all...

IMG_5914.JPG (276.75 KiB) Viewed 3690 times

... is PCB in upside down.. and cable in the way it normally goes, which makes the board pointless... But if I flip the cable and board, it should still work the same , but nope.

I've built up 2 boards, even swapped the side of the PCB the connector goes on.. removed the mod resistors.. I literally just rotated the connector on the PCB...

Capture.PNG (34.93 KiB) Viewed 3690 times

Can only think it doesn't like the drive ID's wired all together, but shouldn't matter, and the H5 is wired like that anyway

EDIT:
Build up a 3rd board and cut the drive ID lines which are joined and still no luck, WTF is going on, this shouldn't be this hard

EDIT2:
Wonder if its now because the drive ID selects are broken

EDIT3:
Nope still not working

EDIT4:
Testing it out both connections, pin8 is in the same location on both connectors How can it be straight-through when the second connector is flipped around.. I wonder if I should have literally swapped the 2 ends of the connector rather than rotating the whole thing

Edit5:
Maybe pin 1 becomes "pin 2" at the opposite end of the cable

EDIT6:
OK I figured it out.. I have the MPF connector rotated on the PCB and on the schematic

[exxos]

Gone back to the SMT printer and trying to build up a few simms to see how I get on

IMG_5926.JPG (232.1 KiB) Viewed 3629 times

IMG_5925.JPG (230.74 KiB) Viewed 3629 times

[exxos]

Melting away..

IMG_5928.JPG (315.98 KiB) Viewed 3619 times

Just thought it was cool enough to video

[exxos]

Must have done somewhere around 100 simms.. bored now

Just finishing the last batch in the UScleaner.. Then will start testing on Monday.. assuming my STE still works after been sat on the shelf for a few weeks...

IMG_5934.JPG (335.87 KiB) Viewed 3572 times

[exxos]

This is gonna keep me busy for a while...

IMG_5937.JPG (355.76 KiB) Viewed 3527 times

IMG_5938.JPG (447.91 KiB) Viewed 3527 times

IMG_5939.JPG (270.75 KiB) Viewed 3527 times

[sporniket]

Good, it gives me some time to think about what to put in my basket this month...

[exxos]

Got the fixed boards and built one up just So now I can use my MPF920 drives on original machines without the twist in the ribbon cable. It also has the "missing" 1772 pullup resistors, hence why power also goes to the PCB and not just the floppy drive.. I need to find out what the proper connectors are called as just used some header pins... It also shouldn't matter about changing the floppy ID on the drive now either.. need to test that next..

IMG_6051.JPG (227.02 KiB) Viewed 3422 times

IMG_6052.JPG (257.49 KiB) Viewed 3422 times

IMG_6053.JPG (273.05 KiB) Viewed 3422 times

IMG_6054.JPG (255.69 KiB) Viewed 3422 times

[exxos]

Finally found the TOS206 decoder PCBs !

I need to setup my paste printer again next and create a profile for these next...

IMG_6080.JPG (457.47 KiB) Viewed 3330 times

IMG_6081.JPG (291.13 KiB) Viewed 3326 times

[exxos]

Don't clean the nozzles they say...

IN YOUR FACE INSTRUCTIONS!!

IMG_6084.JPG (137.76 KiB) Viewed 3318 times

[exxos]

Been experimenting with paste.. I think as the past ends up "high" it doesn't need to fill the whole pad. So while this looks like to little, its actually to much if anything. Once it spreads it looks fine. My previous one I filled the pad and it was really blobby looking afterwards. I think the IC itself doesn't lay totally flat because of it..

Capture.PNG (1.45 MiB) Viewed 3307 times

2.PNG (1.06 MiB) Viewed 3307 times