Sporniket's log on hardware stuff

Blogs & guides and tales of woo by forum members.
User avatar
sporniket
Posts: 953
Joined: Sat Sep 26, 2020 9:12 pm
Location: France
Contact:

Re: Sporniket's log on hardware stuff

Post by sporniket »

Those legacy TV circuitry with some specialty RF components are awfuls...

Nonetheless, here is the last subsheet for the video.

subsheet_403-PAL-NTSC encoding or CSYNC.pdf
(119.47 KiB) Downloaded 92 times

Half of the next sheet is about analog circuitry again... progress will be slow, but I am near the end !
User avatar
sporniket
Posts: 953
Joined: Sat Sep 26, 2020 9:12 pm
Location: France
Contact:

Re: Sporniket's log on hardware stuff

Post by sporniket »

Today schematics is the pair of extended game ports... and I could not fit it inside a single sheet.

subsheet_500-J500 J501 — Gamepad ports.pdf
(123.19 KiB) Downloaded 87 times
subsheet_501-U509 ~~ U512 — Gamepad control.pdf
(84.27 KiB) Downloaded 95 times
User avatar
sporniket
Posts: 953
Joined: Sat Sep 26, 2020 9:12 pm
Location: France
Contact:

Re: Sporniket's log on hardware stuff

Post by sporniket »

Now starting the dma sound path... today will be the DACs

subsheet_502-U500~~U503 - DMA Sound DAC.pdf
(95.58 KiB) Downloaded 78 times

edit: I was motivated enough to finish the pre-amp and filtering (before the lmc1992)

subsheet_503-U504~~U507 — Sound amp. & filter.pdf
(87.79 KiB) Downloaded 88 times

At first, I wanted to fit all those circuit into one subsheet... not a good idea... :lol:

it_could_have_been_worse.jpg
it_could_have_been_worse.jpg (352.79 KiB) Viewed 4395 times
User avatar
sporniket
Posts: 953
Joined: Sat Sep 26, 2020 9:12 pm
Location: France
Contact:

Re: Sporniket's log on hardware stuff

Post by sporniket »

And the end of the audio path... Did you know that "microwire" was just a reference to the microwire protocol and not the nickname of the LMC1992 ?

subsheet_504-U508 — Sound mix and output.pdf
(96.45 KiB) Downloaded 83 times

The end is near... one last sheet to capture. Then I will release a beta version before the final release...
User avatar
sporniket
Posts: 953
Joined: Sat Sep 26, 2020 9:12 pm
Location: France
Contact:

Re: Sporniket's log on hardware stuff

Post by sporniket »

The last sheet. After all those analog circuitry, it was quite quick to capture the RAM and the jumper pads...

subsheet_600-U600~~U603 – RAM modules.pdf
(86.67 KiB) Downloaded 79 times
subsheet_601-E[0..7] — Jumper pads.pdf
(60.92 KiB) Downloaded 80 times

The github repository is up to date.

So, now I will rework a little the whole project, tweak here and there to look better. Then I will create a noob question for proofreading the beta-version, then after that, I will post a final release in the schematics subsection. (of course, the release will also be hosted at github, and I might ask to be put on the atari document archive sites, too).
User avatar
sporniket
Posts: 953
Joined: Sat Sep 26, 2020 9:12 pm
Location: France
Contact:

Re: Sporniket's log on hardware stuff

Post by sporniket »

This is an updated version of the PAL/NTSC encoding circuit, with
  • customs symbols for the variable coils and delay line. I studied this part of the schematics on the Falcon and Mega STE for those components
  • updated comments
subsheet_403-PAL-NTSC encoding or CSYNC.pdf
(134.33 KiB) Downloaded 73 times

edit : fixed the pdf, too hasty, I forgotten to validate some comment edits... now the file is good.

edit 2 : starting to mess with Kicad footprints... By luck, the Atari Document Archive has a gerber of a "Falcon" motherboard (in fact there is a text stating that it is a "Sparrow", the prototype of the Falcon), where I could take the measurements for those footprints.

2021-06-23-L403-footprint.png
2021-06-23-L403-footprint.png (12.62 KiB) Viewed 4241 times
2021-06-23-DL1-footprint.png
2021-06-23-DL1-footprint.png (14.45 KiB) Viewed 4241 times

Next step is learning FreeCad and and a 3d model of each one...
User avatar
sporniket
Posts: 953
Joined: Sat Sep 26, 2020 9:12 pm
Location: France
Contact:

Re: Sporniket's log on hardware stuff

Post by sporniket »

One delay line...

2021-06-23-DL1-topside.png
2021-06-23-DL1-topside.png (11.6 KiB) Viewed 4235 times
2021-06-23-DL1-solderside.png
2021-06-23-DL1-solderside.png (13.46 KiB) Viewed 4235 times
User avatar
sporniket
Posts: 953
Joined: Sat Sep 26, 2020 9:12 pm
Location: France
Contact:

Re: Sporniket's log on hardware stuff

Post by sporniket »

The first release candidate of the schematics is ready, I need proofreader to spot typos :
c300780-001--Atari-STe-Motherboard.pdf
(2.44 MiB) Downloaded 91 times
By the way, the github release candidate is here : https://github.com/sporniket/retro-comp ... v1.0.0.rc1

I also did the 3d model for the variable coils :

2021-06-24-vcoil-topside.png
2021-06-24-vcoil-topside.png (19.25 KiB) Viewed 4173 times
2021-06-24-vcoil-solderside.png
2021-06-24-vcoil-solderside.png (15.35 KiB) Viewed 4173 times
User avatar
sporniket
Posts: 953
Joined: Sat Sep 26, 2020 9:12 pm
Location: France
Contact:

Re: Sporniket's log on hardware stuff

Post by sporniket »

Busy addressing the errors and warning of Kicad's ERC for the release candidate #2... and I found a rabbit hole to explore from time to time too...

2021-06-30--rabbit-hole.png
2021-06-30--rabbit-hole.png (146.16 KiB) Viewed 4009 times

This is done by extracting the silkscreen and the component side soldermask, from the field service manual of the STe (print to pdf each page of interest), put to scale (Gimp) and converted into footprints (Kicad's "Bitmap2component" tool) targeted at the Eco 1 and 2 layers.

I have already done the cut at the bottom right. The render parameter : not realist to show the 2 Eco layers, and wait one long minute.

This is out of the scope I have set for myself (the scope being the schematics), but some groundwork will never hurt.
User avatar
exxos
Site Admin
Site Admin
Posts: 23437
Joined: Wed Aug 16, 2017 11:19 pm
Location: UK
Contact:

Re: Sporniket's log on hardware stuff

Post by exxos »

Looks cool to see a render of the STE board. :thumbup:
https://www.exxosforum.co.uk/atari/ All my hardware guides - mods - games - STOS
https://www.exxosforum.co.uk/atari/store2/ - All my hardware mods for sale - Please help support by making a purchase.
viewtopic.php?f=17&t=1585 Have you done the Mandatory Fixes ?
Just because a lot of people agree on something, doesn't make it a fact. ~exxos ~
People should find solutions to problems, not find problems with solutions.
Post Reply

Return to “MEMBER BLOGS”