Page 1 of 9

ALPHA MODIFICATIONS

Posted: Sun Sep 09, 2018 9:27 pm
by exxos
Started a new thread for "must do" fixes and mods etc.

Re: ALPHA MODIFICATIONS

Posted: Sun Sep 09, 2018 9:35 pm
by exxos
JUMPER PADS
links.jpg
links.jpg (80.51 KiB) Viewed 1619 times

SJ1 & SJ2 are the 2 solder pads like on the STFM near the blitter. Pads must be shorted when NOT using the blitter, and OPEN when using the blitter. For now I would suggest not fitting the blitter.

SJ5 is the clock line for the CPU, this needs to be soldered to allow 8MHz clock to CPU.

SJ3 & SJ4 Need to both be linked.

(Jumpers were there with intention of adding boosters without cutting tracks at a later date )

Jumper next to the ROM is the TOS104 / TOS102 select line.

Re: ALPHA MODIFICATIONS

Posted: Mon Sep 10, 2018 10:05 am
by exxos
RESET FIX

First is the short as found by icky on the reset circuit viewtopic.php?f=19&t=1171#p9633


The red circle shows the resistor shorting out VCC to the highlighted yellow line..
1.JPG
1.JPG (55.25 KiB) Viewed 1579 times

SOLUTION


STEP 1:
s1.JPG
s1.JPG (53.48 KiB) Viewed 1579 times
Cut the tracks on the bottom of the pcb where the yellow lines are.



STEP 2:
s3.JPG
s3.JPG (56.88 KiB) Viewed 1579 times
Solder a wire on the bottom of the PCB to join the pads highlighted with a yellow circle.

DONE:

Re: ALPHA MODIFICATIONS

Posted: Mon Sep 10, 2018 10:24 pm
by Icky
exxos wrote:
Mon Sep 10, 2018 10:05 am
If anyone can post a image of this fix then it would help...
As requested two images. Excuse the messy soldering / flux etc on the underside :oops:

IMG_3034.png
IMG_3034.png (419.7 KiB) Viewed 1545 times

Track cuts are under the wire patch

IMG_3032 (1).png
IMG_3032 (1).png (367.9 KiB) Viewed 1545 times

Re: ALPHA MODIFICATIONS

Posted: Mon Sep 10, 2018 10:56 pm
by exxos
Icky wrote:
Mon Sep 10, 2018 10:24 pm
As requested two images. Excuse the messy soldering / flux etc on the underside :oops:
:bravo:

Re: ALPHA MODIFICATIONS

Posted: Sun Sep 16, 2018 10:30 pm
by exxos
HSYNC FIX

from here viewtopic.php?f=19&t=1146&start=90#p9961

I ballsed up the Hsync and it needs a fix to bypass the inverter...

d1.JPG
d1.JPG (49.49 KiB) Viewed 1443 times

Re: ALPHA MODIFICATIONS

Posted: Sun Sep 16, 2018 11:19 pm
by Icky
exxos wrote:
Sun Sep 16, 2018 10:30 pm
HSYNC FIX

from here viewtopic.php?f=19&t=1146&start=90#p9961
I just sat down to start doing some work on the board tonight and thought I would tackle this first.

Fix in place but am still getting horizontal scrolling as per video of boot before fix.

Will take a closer look at the circuit to see whats going on.

Re: ALPHA MODIFICATIONS

Posted: Sun Sep 16, 2018 11:55 pm
by Realloy
After cutting the trace on both sides of R920 ,,,, measure between D7 and the cut free R920 i get zero ohm, those two point must go to positive plane in pcb, so i guess no need to move the R920.

And also i noticed that the holes for the PSU is mirrored on the PCB.. Maybe you already know this..

Re: ALPHA MODIFICATIONS

Posted: Mon Sep 17, 2018 12:10 am
by exxos
Realloy wrote:
Sun Sep 16, 2018 11:55 pm
After cutting the trace on both sides of R920 ,,,, measure between D7 and the cut free R920 i get zero ohm, those two point must go to positive plane in pcb, so i guess no need to move the R920.
ahh yep, The left link wire isn't needed as the resistor itself actually connects to vcc.. will update the info...

Re: ALPHA MODIFICATIONS

Posted: Mon Sep 17, 2018 8:33 pm
by Realloy
i can see all the chips have a decoupling capacitor,,, but what about BAD DMA ? is there one and where? or is it not necessary?