ABOUT THE STE V1 BOOSTER 2017 - 2020

Help & information about the STE V1 series boosters.
Locked
User avatar
exxos
Site Admin
Site Admin
Posts: 10384
Joined: Wed Aug 16, 2017 11:19 pm
Location: UK
Contact:

ABOUT THE STE V1 BOOSTER 2017 - 2020

Post by exxos » Fri Aug 18, 2017 6:53 pm

Image

Image

The STE 32MHz Booster is comprised of 2 parts. The CPU booster itself and the Fast ROM board which replaces the older slower TOS ROM's.

Results above are the STE running GB6 at 32MHz CPU & ROM. This gives a huge boost in ROM/GEM speeds and also huge boost in Integer Division. This booster can be switched back to 8MHz by linking the SW wire to GND. When the wire is left disconnected the 32MHz boost is active and is its default operating mode.

This kit requires the CPU socket to be removed and the booster installed in its place.

STE V1 HOME
http://www.exxoshost.co.uk/atari/last/V1STE/index.htm

STORE LINK
https://www.exxoshost.co.uk/atari/last/storenew/#0147

If you are looking for help with this booster, please open up a new topic in this section.
https://www.exxoshost.co.uk/atari/ All my hardware guides - mods - games - STOS
https://www.exxoshost.co.uk/atari/store2/ - All my hardware mods for sale - Please help support by making a purchase.

User avatar
exxos
Site Admin
Site Admin
Posts: 10384
Joined: Wed Aug 16, 2017 11:19 pm
Location: UK
Contact:

Re: ABOUT THE STE V1 BOOSTER

Post by exxos » Fri May 01, 2020 2:24 pm

2020 BATCH.


Is almost identical to the original STE V1 design. It fits and works in exactly the same way as before. Probably the only notable difference is that the corner of the board is now "pre-cut" at the PCB factory to miss machines with a socketed blitter.

IMG_5097.JPG
IMG_5097.JPG (417.41 KiB) Viewed 148 times


THE FAQ

I get asked about the plug-in version a fair bit. This was abandoned because there are just too many variations on sockets.. Reliability issues in assembly and long-term operation. Also as it was running at 40MHz on a basically experimental firmware, there was some issues which could not be resolved in a 22V10 GAL. In part this is why the current 2020 batch of V1 is more expensive than before, because I basically had to write off all the plug-in boards.

Could all the be resolved I hear you ask ? well the short answer is yes but I just do not have the time to work on the STFM stuff, nevermind the STE. while my 64MHz SEC booster may one day be ported over to the STE..Running a 64MHz only CPU is not going to yield hardly any speed gain over 32MHz.

Basically for starters, the ROM is maxed out at 32MHz. While these are problems we are working on currently with the SEC booster (flash and fast ram etc) but it is likely the long way off because again, we are working on so many projects at once that progress is always incredibly slow. The STE would it need its own version of the project could be done, but again I do not think it is really worth spending time on.. Because the SEC booster is about 95% wired up as a 020 CPU. Only once we have a 64MHz 020 running on the SEC design, will I consider porting it over to the STE. Of course we still have to complete the SEC work and design and test the 020 CPU yet.. so we are easily the year away.

As I said many times in the past, there is nothing to stop people from designing a alt-ram addon board for the STE booster. Its more than capable of interfacing with a external RAM board and running at 32mhz. That would make a extremely fast system!
https://www.exxoshost.co.uk/atari/ All my hardware guides - mods - games - STOS
https://www.exxoshost.co.uk/atari/store2/ - All my hardware mods for sale - Please help support by making a purchase.

User avatar
exxos
Site Admin
Site Admin
Posts: 10384
Joined: Wed Aug 16, 2017 11:19 pm
Location: UK
Contact:

Re: ABOUT THE STE V1 BOOSTER

Post by exxos » Mon May 18, 2020 6:49 pm

ADDENDUM

As mentioned *somewhere* these boosters work best on machines which have a external blitter IC.

I am unable to test, but integrated blitter machines may need a resistor changing on the board to function correctly.


KNOWN ISSUES

Machine will not boot without pressing the reset button.

Solder a 22uF capacitor across C100 or replace it with a higher value.

IMG_5184.JPG
IMG_5184.JPG (131.33 KiB) Viewed 67 times
https://www.exxoshost.co.uk/atari/ All my hardware guides - mods - games - STOS
https://www.exxoshost.co.uk/atari/store2/ - All my hardware mods for sale - Please help support by making a purchase.

Locked

Return to “STE V1 SERIES 32MHz BOOSTER”