Page 2 of 2

Re: STE Dual TOS switcher widget

Posted: Mon Jan 22, 2018 9:37 am
by rubber_jonnie
ube wrote: Fri Jan 19, 2018 5:48 pm Main problem with the first one is that the peg for mounting the floppy is right besides the header. And mounting it using a female header on the header-board, below the dualTOS, won’t work since it’ll hit the motherboard. At least I think came to that conclusion when I looked into it.
It does actually clear the floppy peg, though it is a snug fit:
IMG_20180118_224320.jpg
IMG_20180118_224320.jpg (3.92 MiB) Viewed 7196 times
I think with a short enough set of header pins, it would fit below, though again, it would be pretty snug.

Re: STE Dual TOS switcher widget

Posted: Mon Jan 22, 2018 11:11 am
by exxos
On future boards I will move the header towards the edge of the board.. Though not sure if another batch will be done or not yet, got 200pcbs made last time so may never all sell.

Re: STE Dual TOS switcher widget

Posted: Mon Jan 22, 2018 2:18 pm
by rubber_jonnie
If I get the urge to tinker with it, I will see how easy it is to put underneath.

Re: STE Dual TOS switcher widget

Posted: Wed Jan 24, 2018 12:20 am
by ube
exxos wrote: Mon Jan 22, 2018 11:11 am On future boards I will move the header towards the edge of the board.. Though not sure if another batch will be done or not yet, got 200pcbs made last time so may never all sell.
Future boards will come with a footprint for adding an optional ATTiny as well, right? :)

Re: STE Dual TOS switcher widget

Posted: Fri Jan 26, 2018 11:38 am
by rubber_jonnie
Might even work with right angled header pins:
90DegHEAD.PNG
90DegHEAD.PNG (46.23 KiB) Viewed 7152 times

Re: STE Dual TOS switcher widget

Posted: Fri Jan 26, 2018 12:01 pm
by exxos
ube wrote: Wed Jan 24, 2018 12:20 am Future boards will come with a footprint for adding an optional ATTiny as well, right? :)
Possible yes... though depends on if this is to be part of the design , or optional addon.

Re: STE Dual TOS switcher widget

Posted: Fri Jan 26, 2018 1:22 pm
by rubber_jonnie
exxos wrote: Fri Jan 26, 2018 12:01 pm
ube wrote: Wed Jan 24, 2018 12:20 am Future boards will come with a footprint for adding an optional ATTiny as well, right? :)
Possible yes... though depends on if this is to be part of the design , or optional addon.
Part of the board would be amazing :)

Re: STE Dual TOS switcher widget

Posted: Wed Jan 31, 2018 2:44 pm
by ube
gnZwukn_d.jpg
gnZwukn_d.jpg (84.27 KiB) Viewed 1221 times

Cr2032 for scale.

Re: STE Dual TOS switcher widget

Posted: Wed Jan 31, 2018 4:08 pm
by rubber_jonnie
Ooooh, that's weeeny!! :o

Re: STE Dual TOS switcher widget

Posted: Sun Mar 11, 2018 9:18 pm
by tzok
Nice, but...

7370304900_1514402582.jpg
7370304900_1514402582.jpg (105.76 KiB) Viewed 1220 times
1264983400_1514402585.jpg
1264983400_1514402585.jpg (147.45 KiB) Viewed 1220 times

2 because one for A:/B: swap, and one for TOS 1.62/2.06.