Module ESP8266 without TF on Amiga
Moderators: terriblefire, Terriblefire Moderator
Re: Module ESP8266 without TF on Amiga
U mean this RS232 to TTL converter?
ESP8266 working definitely
ESP8266 working definitely
-
- Moderator Team
- Posts: 5389
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: Module ESP8266 without TF on Amiga
Yes. Test that then drop the baud rate to 19200 if it still doesnt work.
To change the baud rate You'll need to edit envarc:sana2/slip0.config and then also slattach again at 38400 and issue a set bitate commands, save, reset.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
Re: Module ESP8266 without TF on Amiga
Where is this folder in RAM Disk?You'll need to edit envarc:sana2/slip0.config
If is this one there is setup
Code: Select all
serial.device 0 115200 192.168.240.2
so again connect to linux ?and then also slattach again at 38400 and issue a set bitate commands, save, reset.
-
- Moderator Team
- Posts: 5389
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: Module ESP8266 without TF on Amiga
OK STOPkulamario wrote: ↑Fri Apr 17, 2020 7:39 pmWhere is this folder in RAM Disk?You'll need to edit envarc:sana2/slip0.config
If is this one there is setupCode: Select all
serial.device 0 115200 192.168.240.2
so again connect to linux ?and then also slattach again at 38400 and issue a set bitate commands, save, reset.
Edit that in ENVARC: not RAM:ENV
Set the 115200 to 38400 then Reboot and try again.
That value in ENVARC must match the bitrate you set in the ESP.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
-
- Moderator Team
- Posts: 5389
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: Module ESP8266 without TF on Amiga
One last thing... now that you have the ESP up on your LAN you can telnet from your LAN on port 7777 to it if you can find it. Your router may have a homepage that lists it?
Mine appears as ESP_04F1DB for example.
Mine appears as ESP_04F1DB for example.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
Re: Module ESP8266 without TF on Amiga
Edit that in ENVARC
Nothing change
Nothing change
Re: Module ESP8266 without TF on Amiga
Yes my esp8266 is login to network I see this in what devices is connected to router
But how to check in telnet ?
U mean from linux ?
But how to check in telnet ?
U mean from linux ?
Code: Select all
sudo telnet 192.168.240.1
-
- Moderator Team
- Posts: 5389
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: Module ESP8266 without TF on Amiga
No whatever its IP is on the lan... telnet from your PC to it on port 7777.kulamario wrote: ↑Fri Apr 17, 2020 8:29 pm Yes my esp8266 is login to network I see this in what devices is connected to router
But how to check in telnet ?
U mean from linux ?Code: Select all
sudo telnet 192.168.240.1
You need to take it from here. Its your hardware.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
-
- Moderator Team
- Posts: 5389
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: Module ESP8266 without TF on Amiga
The value in ENVARC:sana2/slip0.config must match the bitrate set in the ESP module.
If you want to be lazy edit the install_script and replace 115200 with your desired bitrate and rerun it.
TBH i would set it to 9600 both sides to start with and get it going at that speed first.
If you know what your ESP router is currently set to then you can change it by
I'm not sure what actual speed you will get out of an A500 serial port. 9600 should be a safe starting point.
EDIT: You also need to reboot after editing the ENVARC settings.
If you want to be lazy edit the install_script and replace 115200 with your desired bitrate and rerun it.
TBH i would set it to 9600 both sides to start with and get it going at that speed first.
If you know what your ESP router is currently set to then you can change it by
Code: Select all
sudo slattach -p slip -s BAUD_RATE /dev/ttyUSB0&
EDIT: You also need to reboot after editing the ENVARC settings.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
Re: Module ESP8266 without TF on Amiga
I'll check everything this when I come back from work
But I have question
This slip router working on same rules like plipbox ?
I just want tell I have plipbox in home and this plipbox no run maybe is real my modem is not good for this ?
I fight with plipbox for few days and no success
I have modem F2000
Internet from eir.ie
Another thing maybe my ports in amiga is faulty
Is possible to check ports amiga via some terminal ?
But I have question
This slip router working on same rules like plipbox ?
I just want tell I have plipbox in home and this plipbox no run maybe is real my modem is not good for this ?
I fight with plipbox for few days and no success
I have modem F2000
Internet from eir.ie
Another thing maybe my ports in amiga is faulty
Is possible to check ports amiga via some terminal ?