B39D45CA-A26A-45B4-B002-E7A8A0D9416B.jpeg (2.76 MiB) Viewed 15167 times
EE5527FE-8272-40B6-834D-97E2D07F0506.jpeg (2.4 MiB) Viewed 15167 times
C82D383E-531D-4A53-848D-E39F43109A5A.jpeg (3.11 MiB) Viewed 15167 times
2D3B77D9-8E09-454E-AC62-54DEF16E4C30.jpeg (2.5 MiB) Viewed 15167 times
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
A little bit concerned about the process here. I think my choice to use a 7 mi clearance was wise... they only just managed it
jebus.JPG (108.56 KiB) Viewed 15132 times
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
supaduper wrote: ↑Mon Nov 19, 2018 6:35 pm
They look great Steve and a +1 for the packaging by JLC
Perfect box for sending 328s to you in
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
terriblefire wrote: ↑Mon Nov 19, 2018 6:41 pm
A little bit concerned about the process here. I think my choice to use a 7 mi clearance was wise... they only just managed it
wow! The last boards I got were from JLC.. will see if I can check quality on one later..
https://www.exxosforum.co.uk/atari/ All my hardware guides - mods - games - STOS https://www.exxosforum.co.uk/atari/store2/ - All my hardware mods for sale - Please help support by making a purchase. viewtopic.php?f=17&t=1585 Have you done the Mandatory Fixes ?
Just because a lot of people agree on something, doesn't make it a fact. ~exxos ~
People should find solutions to problems, not find problems with solutions.
Mine isn't perfect, but not as bad as yours I think..
555.jpg (144.88 KiB) Viewed 15120 times
666.jpg (149.82 KiB) Viewed 15120 times
https://www.exxosforum.co.uk/atari/ All my hardware guides - mods - games - STOS https://www.exxosforum.co.uk/atari/store2/ - All my hardware mods for sale - Please help support by making a purchase. viewtopic.php?f=17&t=1585 Have you done the Mandatory Fixes ?
Just because a lot of people agree on something, doesn't make it a fact. ~exxos ~
People should find solutions to problems, not find problems with solutions.
terriblefire wrote: ↑Mon Nov 19, 2018 6:41 pm
A little bit concerned about the process here. I think my choice to use a 7 mi clearance was wise... they only just managed it
wow! The last boards I got were from JLC.. will see if I can check quality on one later..
Judging by this.. Its the drill holes that are the problem. SMD pads are fine. in the next revision i'll tighten the trace to trace and give more clearance to the drill point. Probably trace to trace 6.5mil and Trace to pad 8mil.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
terriblefire wrote: ↑Mon Nov 19, 2018 7:06 pm
Judging by this.. Its the drill holes that are the problem. SMD pads are fine. in the next revision i'll tighten the trace to trace and give more clearance to the drill point. Probably trace to trace 6.5mil and Trace to pad 8mil.
The 0.8mm holes look ok on my board, looks like the smaller drill holes are running out..
Might be worth reporting a quality problem to them ?
https://www.exxosforum.co.uk/atari/ All my hardware guides - mods - games - STOS https://www.exxosforum.co.uk/atari/store2/ - All my hardware mods for sale - Please help support by making a purchase. viewtopic.php?f=17&t=1585 Have you done the Mandatory Fixes ?
Just because a lot of people agree on something, doesn't make it a fact. ~exxos ~
People should find solutions to problems, not find problems with solutions.
alenppc wrote: ↑Mon Nov 19, 2018 7:59 pm
That board looks a bit thick... I hope it's just the picture, as 1.6 mm won't fit in the riser
Its 1.6mm. All my TF328s have been that. They fit no issue.
EDIT: Although i will say they were supposed to do bevelled edges and they didnt.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."