Page 1 of 28

The TF330 is here

Posted: Mon Nov 19, 2018 6:03 pm
by terriblefire
First look at the new board
B39D45CA-A26A-45B4-B002-E7A8A0D9416B.jpeg
B39D45CA-A26A-45B4-B002-E7A8A0D9416B.jpeg (2.76 MiB) Viewed 15047 times
EE5527FE-8272-40B6-834D-97E2D07F0506.jpeg
EE5527FE-8272-40B6-834D-97E2D07F0506.jpeg (2.4 MiB) Viewed 15047 times
C82D383E-531D-4A53-848D-E39F43109A5A.jpeg
C82D383E-531D-4A53-848D-E39F43109A5A.jpeg (3.11 MiB) Viewed 15047 times
2D3B77D9-8E09-454E-AC62-54DEF16E4C30.jpeg
2D3B77D9-8E09-454E-AC62-54DEF16E4C30.jpeg (2.5 MiB) Viewed 15047 times

Re: The TF330 is here

Posted: Mon Nov 19, 2018 6:35 pm
by supaduper
They look great Steve and a +1 for the packaging by JLC :)

Re: The TF330 is here

Posted: Mon Nov 19, 2018 6:41 pm
by terriblefire
A little bit concerned about the process here. I think my choice to use a 7 mi clearance was wise... they only just managed it
jebus.JPG
jebus.JPG (108.56 KiB) Viewed 15012 times

Re: The TF330 is here

Posted: Mon Nov 19, 2018 6:42 pm
by terriblefire
supaduper wrote: Mon Nov 19, 2018 6:35 pm They look great Steve and a +1 for the packaging by JLC :)
Perfect box for sending 328s to you in :)

Re: The TF330 is here

Posted: Mon Nov 19, 2018 6:50 pm
by exxos
terriblefire wrote: Mon Nov 19, 2018 6:41 pm A little bit concerned about the process here. I think my choice to use a 7 mi clearance was wise... they only just managed it
wow! The last boards I got were from JLC.. will see if I can check quality on one later..

Re: The TF330 is here

Posted: Mon Nov 19, 2018 7:04 pm
by exxos
Mine isn't perfect, but not as bad as yours I think..

555.jpg
555.jpg (144.88 KiB) Viewed 15000 times

666.jpg
666.jpg (149.82 KiB) Viewed 15000 times

Re: The TF330 is here

Posted: Mon Nov 19, 2018 7:06 pm
by terriblefire
exxos wrote: Mon Nov 19, 2018 6:50 pm
terriblefire wrote: Mon Nov 19, 2018 6:41 pm A little bit concerned about the process here. I think my choice to use a 7 mi clearance was wise... they only just managed it
wow! The last boards I got were from JLC.. will see if I can check quality on one later..
Judging by this.. Its the drill holes that are the problem. SMD pads are fine. in the next revision i'll tighten the trace to trace and give more clearance to the drill point. Probably trace to trace 6.5mil and Trace to pad 8mil.

Re: The TF330 is here

Posted: Mon Nov 19, 2018 7:07 pm
by exxos
terriblefire wrote: Mon Nov 19, 2018 7:06 pm Judging by this.. Its the drill holes that are the problem. SMD pads are fine. in the next revision i'll tighten the trace to trace and give more clearance to the drill point. Probably trace to trace 6.5mil and Trace to pad 8mil.
The 0.8mm holes look ok on my board, looks like the smaller drill holes are running out..

Might be worth reporting a quality problem to them ?

Re: The TF330 is here

Posted: Mon Nov 19, 2018 7:59 pm
by alenppc
That board looks a bit thick... I hope it's just the picture, as 1.6 mm won't fit in the riser

Re: The TF330 is here

Posted: Mon Nov 19, 2018 8:15 pm
by terriblefire
alenppc wrote: Mon Nov 19, 2018 7:59 pm That board looks a bit thick... I hope it's just the picture, as 1.6 mm won't fit in the riser
Its 1.6mm. All my TF328s have been that. They fit no issue.

EDIT: Although i will say they were supposed to do bevelled edges and they didnt.