This thread is for TF330 performance improvements. All firmwares posted in here are ALPHA and may cause your entire town to be vapourized.
With that said i just got burst read working on the TF330 ...
Firmware are distributed to the usual crowd via email until fire is confirmed as not happening.
TF330 Performance Improvements
Moderators: terriblefire, Terriblefire Moderator
-
- Moderator Team
- Posts: 5389
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
TF330 Performance Improvements
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
Re: TF330 Performance Improvements
Can confirm the `BURST MODE` firmware working great, only the A4000 is edging it !
I think what I will do tomorrow for people wanting to update their firmware if they have a Raspberry pie 2 or 3, is put a link to my 8gb Raspian image with the program app `xc3sprog` already installed ready to go,so you just need to open a Terminal input the commands and away you go.
Just need to follow Stephens great How To video on the Rasp pi set up and info on the dupont cable locations.
Stephens How to video below
Here is my Dupont cable setup
I think what I will do tomorrow for people wanting to update their firmware if they have a Raspberry pie 2 or 3, is put a link to my 8gb Raspian image with the program app `xc3sprog` already installed ready to go,so you just need to open a Terminal input the commands and away you go.
Just need to follow Stephens great How To video on the Rasp pi set up and info on the dupont cable locations.
Stephens How to video below
Here is my Dupont cable setup
- Attachments
-
- RaspberryPi xc3sprog cable.jpg (256.13 KiB) Viewed 7481 times
Re: TF330 Performance Improvements
Great work Steve.
Is the Rev 0 still taking a small speed hit?
Is the Rev 0 still taking a small speed hit?
-
- Moderator Team
- Posts: 5389
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: TF330 Performance Improvements
No they''re both the same now.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
Re: TF330 Performance Improvements
I am leaving mine running AmiWolf3D for a few hours to see if there are any crashes... Run frontier also for a bit without issue.
Re: TF330 Performance Improvements
It's been running for about 4 hrs now without crashes. I think we are good.
Re: TF330 Performance Improvements
I just tried playing DoomAttack with 020optimized C2P routine. It's blazing fast. It also one of the rare games that supports Akiko c2p and it shows how painfully slow that one is. ADoom port is quite a lot slower but still playable.
Re: TF330 Performance Improvements
Wow! Great work guys
-
- Moderator Team
- Posts: 5389
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: TF330 Performance Improvements
Can we check all the CPU variations before we roll it out.
I've tested the MC68030RP33, MC68030RC50 and the MC68EC030RP40.
I've tested the MC68030RP33, MC68030RC50 and the MC68EC030RP40.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
Re: TF330 Performance Improvements
MC68EC030RP40 is all good here