TF Riser Revision 0 Arrives
Moderators: terriblefire, Terriblefire Moderator
-
- Moderator Team
- Posts: 5389
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
TF Riser Revision 0 Arrives
Boards are here.
Keeping in mind that I dont have a firmware for the ARM... Who was after one to help out with dev?
Keeping in mind that I dont have a firmware for the ARM... Who was after one to help out with dev?
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
- arkadiusz.makarenko
- Moderator Team
- Posts: 1208
- Joined: Wed Jun 19, 2019 7:36 am
- Location: Edinburgh
Re: A new riser?
I would like to buy one, please.
PS.
I am staring to look at this : https://www.st.com/resource/en/user_man ... 105256.pdf
I have only boards with f103 which do not have required USB OTG. Any day now I should get f407 dev board, and I will be able to start looking at this properly. Meanwhile I am getting used to CubeIDE,HAL libraries and brilliant debbuging options via ST-Link
PS.
I am staring to look at this : https://www.st.com/resource/en/user_man ... 105256.pdf
I have only boards with f103 which do not have required USB OTG. Any day now I should get f407 dev board, and I will be able to start looking at this properly. Meanwhile I am getting used to CubeIDE,HAL libraries and brilliant debbuging options via ST-Link
Do not trust people. They are capable of greatness.
~ Stanislaw Lem
~ Stanislaw Lem
-
- Moderator Team
- Posts: 5389
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: A new riser?
I'll slip a board in with your TF536.arkadiusz.makarenko wrote: ↑Wed Jan 15, 2020 6:36 pm I would like to buy one, please.
PS.
I am staring to look at this : https://www.st.com/resource/en/user_man ... 105256.pdf
I have only boards with f103 which do not have required USB OTG. Any day now I should get f407 dev board, and I will be able to start looking at this properly. Meanwhile I am getting used to CubeIDE,HAL libraries and brilliant debbuging options via ST-Link
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
- arkadiusz.makarenko
- Moderator Team
- Posts: 1208
- Joined: Wed Jun 19, 2019 7:36 am
- Location: Edinburgh
Re: A new riser?
Great thank you.
Do not trust people. They are capable of greatness.
~ Stanislaw Lem
~ Stanislaw Lem
-
- Moderator Team
- Posts: 5389
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: A new riser?
Started the build...
Waiting for the ARM cpu tomorrow.
One thing to note is that the MCA connector needed the tabs trimmed off to fit due to the way my MCA connector tabs are.
EDIT: I actually think it will be far easier to develop on this board than a dev board.
Waiting for the ARM cpu tomorrow.
One thing to note is that the MCA connector needed the tabs trimmed off to fit due to the way my MCA connector tabs are.
EDIT: I actually think it will be far easier to develop on this board than a dev board.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
Re: TF Riser Revision 0 Arrives
Watching this with great interest and anticipation, particularly with regards to the ARM HID USB part
-
- Moderator Team
- Posts: 5389
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: TF Riser Revision 0 Arrives
You are welcome to rework/integrate your changes to the video system if you want. Spare board for you if you want
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
Re: TF Riser Revision 0 Arrives
Thanks, would appreciate the board for sure, and if/when the ARM USB and RTC is working I'd like to try and integrate (with full credits to all parties) them onto a Firebird module, maybe even a Notport.
PM inbound with address.
PM inbound with address.
Re: TF Riser Revision 0 Arrives
So, it is happening. Amazing.