TF1230 Beta Interest (Open Source)
Moderators: terriblefire, Terriblefire Moderator
Re: TF1230 Beta Interest (Open Source)
have not time now but I will put os 3.2 roms in and see if I get the same problem as you
-
- Posts: 144
- Joined: Sat Dec 19, 2020 11:42 am
- Location: Zielona Gora
Re: TF1230 Beta Interest (Open Source)
I did the ScsiSpeed tests and it's probably a problem with this PLATINUM card.
On other CF cards it works ok and it's like this:
1.Stec 1GB - 2.5 MB / s
2.WD -SiliconDrive 2GB - 3GB / s
3.Kingston 4GB - 3.2GB / s
4.CompactFlash (with Ali) 16GB - 2.8GB / s
5.SD to IDE adapter with 8GB sandisk ultra card - 3,2MB / s
6. 2.5 "HDD Samsung 80GB - 5.4MB / s
I did tests on kickstart 3.1 and only setpatch, loadwb and mufastrom before ScsiSpeed.
Re: TF1230 Beta Interest (Open Source)
Hello
I am not sure if anybody has post about a rev1b yet, if not hope to let you know my findings in a week or two, & any timing fixes if needed..etc
& if people have, then please forgive me well just once
I am not sure if anybody has post about a rev1b yet, if not hope to let you know my findings in a week or two, & any timing fixes if needed..etc
& if people have, then please forgive me well just once
Re: TF1230 Beta Interest (Open Source)
So I just installed 3.2 roms and ehide.device and yes I get the same fault no boot, this is defo software problem, will have a look latermarkus0321 wrote: ↑Sat Sep 18, 2021 6:58 pmBoot without startup-sequence from DF0 drive:
Load module devs: ehide.device => system reboots without messages and reloads from floppy but ehide.device is not loaded in memory and no partitions mounted in system are visible.
I set up the partition with a small 200mb for testing and it will start normally in the controller from the motherboard. I have kickstart 3.1 but I have OS 3.2 installed.
-
- Posts: 144
- Joined: Sat Dec 19, 2020 11:42 am
- Location: Zielona Gora
Re: TF1230 Beta Interest (Open Source)
Today everything works fine for me, yesterday the problem was the CF card on which I had the system installed. Other cards I have work properly with ehide.device and rom 3.1 and 3.2. Well, unless it's a coincidence of a card and software problem at one time.supaduper wrote: ↑Sun Sep 19, 2021 3:26 pmSo I just installed 3.2 roms and ehide.device and yes I get the same fault no boot, this is defo software problem, will have a look latermarkus0321 wrote: ↑Sat Sep 18, 2021 6:58 pm
Boot without startup-sequence from DF0 drive:
Load module devs: ehide.device => system reboots without messages and reloads from floppy but ehide.device is not loaded in memory and no partitions mounted in system are visible.
I set up the partition with a small 200mb for testing and it will start normally in the controller from the motherboard. I have kickstart 3.1 but I have OS 3.2 installed.
I noticed, however, that ehide.device does not want to cooperate with another CF Stec 2GB card, but not always. in this case, I solved the problem by soldering a small MLC 100uF 16V type capacitor to the power pins on the IDE2CF adapter, after this procedure the driver works every time.
-
- Posts: 144
- Joined: Sat Dec 19, 2020 11:42 am
- Location: Zielona Gora
Re: TF1230 Beta Interest (Open Source)
I did one more test and compiled kickstart 3.2 + ehide.device with Remus. Now it works very well even with the card that previously had problems with ehide and loadmodule!markus0321 wrote: ↑Sun Sep 19, 2021 4:44 pmToday everything works fine for me, yesterday the problem was the CF card on which I had the system installed. Other cards I have work properly with ehide.device and rom 3.1 and 3.2. Well, unless it's a coincidence of a card and software problem at one time.
I noticed, however, that ehide.device does not want to cooperate with another CF Stec 2GB card, but not always. in this case, I solved the problem by soldering a small MLC 100uF 16V type capacitor to the power pins on the IDE2CF adapter, after this procedure the driver works every time.
Re: TF1230 Beta Interest (Open Source)
I gave the TF1230 a real work-out over the weekend and IMHO this card hits the economical functional sweet spot with a A1200. I think the word maybe out, as the build components required are disappearing rapidly.
Life is really simple, but we insist on making it complicated - Confucius
-
- Moderator Team
- Posts: 5389
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: TF1230 Beta Interest (Open Source)
Amiga people want cheap. Thats the most important thing for them .
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
Re: TF1230 Beta Interest (Open Source)
I wanted to order soldered bird seeds PCB but I don't know what's going on with these black spots
Would someone be able to explain to me whether this is to be the OK or something is wrong
Would someone be able to explain to me whether this is to be the OK or something is wrong
-
- Moderator Team
- Posts: 5389
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: TF1230 Beta Interest (Open Source)
If its from JLC ignore this. Their rendering software is wrong. Use the CPL files i posted.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."