Page 2 of 23

Re: TF536 Rev 2 Design Complete

Posted: Fri Mar 20, 2020 5:50 pm
by terriblefire
Well if it works I’ll be ordering 50 immediately. Keeping it tight for this run given how many changes

Re: TF536 Rev 2 Design Complete

Posted: Fri Mar 20, 2020 6:11 pm
by mattymuc
Oh that looks like a terrible great Rev 2! Please add me to the list.

Re: TF536 Rev 2 Design Complete

Posted: Fri Mar 20, 2020 6:14 pm
by 8 Bit Dreams
terriblefire wrote:
Fri Mar 20, 2020 5:50 pm
Well if it works I’ll be ordering 50 immediately. Keeping it tight for this run given how many changes
i have no doubt it will :!:
i'll go for 20 as soon as orders are open :P

Ps
maybe it is worth to send one board to @agranlund
he wanted to start to work on Atari ST firmware :arrow: :arrow: :arrow:
So TF536 will work on Atari's at the moment it will be released...just my thoughts

Re: TF536 Rev 2 Design Complete

Posted: Fri Mar 20, 2020 7:10 pm
by arananet
Please addme for one TF536.

Thanks!

Re: TF536 Rev 2 Design Complete

Posted: Fri Mar 20, 2020 11:16 pm
by Danoo
terriblefire wrote:
Fri Mar 20, 2020 5:50 pm
Well if it works I’ll be ordering 50 immediately. Keeping it tight for this run given how many changes
Will definitely like to purchase at least two, when you get to the bulk purchase, will be patiently watching

Re: TF536 Rev 2 Design Complete

Posted: Sat Mar 21, 2020 11:17 pm
by terriblefire
Seem to have missed 2 RNs off the assembly...
Screenshot 2020-03-21 at 23.18.20.png
Screenshot 2020-03-21 at 23.18.20.png (865.35 KiB) Viewed 517 times

Re: TF536 Rev 2 Design Complete

Posted: Sun Mar 22, 2020 7:52 am
by 8 Bit Dreams
Ah, i see, RN2 & RN3 are not populated
thats ok, i like these small badgers 😀

Re: TF536 Rev 2 Design Complete

Posted: Sun Mar 22, 2020 8:13 am
by kulamario
Please add me to list 1xPCB

Re: TF536 Rev 2 Design Complete

Posted: Sun Mar 22, 2020 8:34 am
by amimjf
Hi All,

Been lurking on the TF forms for a while, I think I will take the plunge and build some 536 r2's for my A500++ boards,.. excellent work and collaboration by you all BTW.

I was looking for a pinned message with a BOM so I could start to source parts ?.. The 536 seems achievable with quite a few 68030's from China, but getting 68060's for 360/560/1260 designs sounds like plain luck.

regards.

Re: TF536 Rev 2 Design Complete

Posted: Sun Mar 22, 2020 8:40 am
by terriblefire
amimjf wrote:
Sun Mar 22, 2020 8:34 am
Hi All,

Been lurking on the TF forms for a while, I think I will take the plunge and build some 536 r2's for my A500++ boards,.. excellent work and collaboration by you all BTW.

I was looking for a pinned message with a BOM so I could start to source parts ?.. The 536 seems achievable with quite a few 68030's from China, but getting 68060's for 360/560/1260 designs sounds like plain luck.

regards.
BOMs will be available on github once the beta test phase is complete. Its subject to change until then.

Also... you dont need a full BOM anymore. The boards will come with all passives on already.