Page 5 of 13

Re: REV H1 information and interest

Posted: Wed May 22, 2019 10:51 pm
by exxos
JezC wrote: Wed May 22, 2019 10:45 pm Might only be 24 as PhilC == Forgottenmyname...?
ah yes, good catch. deleted one.

Re: REV H1 information and interest

Posted: Wed May 22, 2019 11:36 pm
by Anzac
With currency conversion £80 is a bit steep for me, but since I don't want the hardware, I can pledge £60 :)

Re: REV H1 information and interest

Posted: Wed May 22, 2019 11:56 pm
by exxos
you get charged £40 for conversion ?!

Re: REV H1 information and interest

Posted: Thu May 23, 2019 7:14 am
by Anzac
No, it's just the difference between currencies.

£60 is 71€ for me, plus paypal fees to send the money, final cost should be around 75€.
So, yeah, maybe I can go a little more, but if I go for £80 it gets real close to 100€ and that makes a difference for me...

I have always tried to support developers and the community, sometimes just by donating in recognition of the work that had been done

I understand that my offer here isn't much and later I'll support the project again if needed, right now, this is what I can do..

Re: REV H1 information and interest

Posted: Thu May 23, 2019 4:30 pm
by exxos
I have a donate button for such payments anyway. Where people just type in the amount they want to donate..

Though I don't use paypal anymore. So its done on credit card. I get charged "non sterling transaction charge" when I do overseas payments, but its normally only about £2 or thereabouts.. of course I don't know what the charges are for other banks..But if the charges are crazy, then I probably suggest just not bothering.

Re: REV H1 information and interest

Posted: Thu May 23, 2019 8:57 pm
by Icky
Have been helping out with some of the routing on the H2. This is the MMU - PLCC and SMT.

Screenshot 2019-05-23 at 20.54.30.png
Screenshot 2019-05-23 at 20.54.30.png (96.3 KiB) Viewed 4777 times

Re: REV H1 information and interest

Posted: Thu May 23, 2019 9:04 pm
by exxos
Looking good! Saving me a lot of torment with not having to click things all day!

:thanksyellow:

Re: REV H1 information and interest

Posted: Sat May 25, 2019 8:25 pm
by Icky
One stripped ST motherboard for exxos to use as a template to check the holes and other dimensions for correct placement on the next Remake board.

This was the broken motherboard that was used as the donor for my STF Remake so did not take too long to strip everything off.

1B49055E-CBE9-4134-8368-350E53176ECA.jpeg
1B49055E-CBE9-4134-8368-350E53176ECA.jpeg (996.95 KiB) Viewed 4752 times

Re: REV H1 information and interest

Posted: Sat May 25, 2019 9:08 pm
by exxos
Thing of beauty... should put it in the motherboard section :)

Re: REV H1 information and interest

Posted: Sat May 25, 2019 10:26 pm
by Icky
exxos wrote: Sat May 25, 2019 9:08 pm Thing of beauty... should put it in the motherboard section :)
Yes even though it has a few ripped tracks, partial reason the motherboard was dead, and is not perfectly flat it is something to behold.

I’ll drop the pic into the motherboard section :)