Getting WFI Working on TF3xx with ESP Module
Moderators: terriblefire, Terriblefire Moderator
Re: Getting WFI Working on TF3xx with ESP Module
A quick question , is this just for 330 and 360 cards only?
If it ain't broke, test it to Destruction.
-
- Moderator Team
- Posts: 5389
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: Getting WFI Working on TF3xx with ESP Module
Yes. The CD32 has the UART pins on the edge connector.
EDIT: I could have added this to the A1200 card but people use PCMCIA there. No chance of it on an A500 card would required a full UART chip.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
Re: Getting WFI Working on TF3xx with ESP Module
Thanks, that explains it.
If it ain't broke, test it to Destruction.
Re: Getting WFI Working on TF3xx with ESP Module
Did some nasty soldering and got my TF-330 online. Brilliant stuff.
Re: Getting WFI Working on TF3xx with ESP Module
Has anyone tried baud rates above 115200?
-
- Moderator Team
- Posts: 5389
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: Getting WFI Working on TF3xx with ESP Module
No. ESP Slip router doesnt go above that from the docs.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
Re: Getting WFI Working on TF3xx with ESP Module
I can run it at 216000bps but the CPU starts really struggling when you up the speeds. I think that 1mbps shouldn't be an issue with TF360 (If that's the only bottle neck). I think the documentation only tells that it defaults to 115200 since some USB devices max out at that rate but 21600 bps can be achieved just by editing envarc:sana2/slip0.config and setting the bitrate in the esp console. If that fails you can probably try a slower rate, say 201600 that still produces a nice boost.
-
- Moderator Team
- Posts: 5389
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: Getting WFI Working on TF3xx with ESP Module
I'm very surprised the CD32 uart can handle that at all. I wouldn't expect it to get much faster.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
Re: Getting WFI Working on TF3xx with ESP Module
Ahh well I benefit from not knowing what I'm doing.terriblefire wrote: ↑Mon May 04, 2020 10:00 pmI'm very surprised the CD32 uart can handle that at all. I wouldn't expect it to get much faster.
-
- Moderator Team
- Posts: 5389
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: Getting WFI Working on TF3xx with ESP Module
Keep going. Tell me what the limit is.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."