@terriblefire will give that new firmware a try tomorrow.
My rev 1 is installed in a finicky 500 plus, so cant really use it to test as it took me ages to get it to work reliably in it. (Computers fault not TF536)
I do have a few spare caps if you think its worth trying to change them.
TF536 Rev 2 Design Complete (all gone)
Moderators: terriblefire, Terriblefire Moderator
Re: TF536 Rev 2 Design Complete (all gone)
If it ain't broke, test it to Destruction.
-
- Moderator Team
- Posts: 5389
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: TF536 Rev 2 Design Complete (all gone)
Well on that firmware everything is running at 8Mhz. which is weird... only difference is the pull ups.PhilC wrote: ↑Sat May 09, 2020 10:34 pm @terriblefire will give that new firmware a try tomorrow.
My rev 1 is installed in a finicky 500 plus, so cant really use it to test as it took me ages to get it to work reliably in it. (Computers fault not TF536)
I do have a few spare caps if you think its worth trying to change them.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
Re: TF536 Rev 2 Design Complete (all gone)
Good so far. I'm able to boot the exxos IDE to desktop and run stuff from it.terriblefire wrote: ↑Sat May 09, 2020 10:36 pm
Well on that firmware everything is running at 8Mhz. which is weird... only difference is the pull ups.
If I have a CF connected to the 536 ide then the computer doesnt boot but that's an obvious conflict of the two Ide I suspect?
If it ain't broke, test it to Destruction.
-
- Moderator Team
- Posts: 5389
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: TF536 Rev 2 Design Complete (all gone)
OK.. im almost convinced its caps.PhilC wrote: ↑Sun May 10, 2020 12:30 pmGood so far. I'm able to boot the exxos IDE to desktop and run stuff from it.terriblefire wrote: ↑Sat May 09, 2020 10:36 pm
Well on that firmware everything is running at 8Mhz. which is weird... only difference is the pull ups.
If I have a CF connected to the 536 ide then the computer doesnt boot but that's an obvious conflict of the two Ide I suspect?
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
Re: TF536 Rev 2 Design Complete (all gone)
@terriblefire I presume it would be unreliable on an Amiga also if that was the case?
I've left it running Gembench and it happily runs that, albeit slowly. It 2 bombs when I tried to run Frontier though.
I've got a few of the larger 100nf caps, not sure about the smaller ones though, so just let me know what you want me to try.
I've left it running Gembench and it happily runs that, albeit slowly. It 2 bombs when I tried to run Frontier though.
I've got a few of the larger 100nf caps, not sure about the smaller ones though, so just let me know what you want me to try.
If it ain't broke, test it to Destruction.
-
- Moderator Team
- Posts: 5389
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: TF536 Rev 2 Design Complete (all gone)
I got paranoid so i dug out the CDTV. Its working fine :/
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
Re: TF536 Rev 2 Design Complete (all gone)
We have a terriblefire
Re: TF536 Rev 2 Design Complete (all gone)
Good news, so just a case of tweaking the firmware I take it?terriblefire wrote: ↑Sun May 10, 2020 2:37 pm I got paranoid so i dug out the CDTV. Its working fine :/
If it ain't broke, test it to Destruction.
-
- Moderator Team
- Posts: 5389
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: TF536 Rev 2 Design Complete (all gone)
Think so. Maybe just need to let @agranlund work his magic when he gets his.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
Re: TF536 Rev 2 Design Complete (all gone)
Sounds like a plan to me.terriblefire wrote: ↑Sun May 10, 2020 3:01 pm Think so. Maybe just need to let @agranlund work his magic when he gets his.
If it ain't broke, test it to Destruction.