My summer project: A colour Stacy

General discussions or ideas about hardware.
Post Reply
User avatar
derkom
Moderator
Moderator
Posts: 1208
Joined: Sun Jul 29, 2018 6:45 pm

Re: My summer project: A colour Stacy

Post by derkom »

I finally found some time today to diagnose the problem, and long story short, the Stacy is fixed.

I decided that rather than start reflowing or checking all the connections between the major chips, I would just capture data off every pin on the Glue, MMU, and Shifter. I can do that pretty rapidly and then compare data between like pins. As anticipated, the Glue was producing 15 kHz sync, despite the system being booted in mono. Didn't take me too long there to notice that RW on the Glue was stuck high, where it was quite active on MMU. This led to the discovery that RW on Glue was connected to the new 2.2k pullup, but not to RW on MMU, Shifter, or 68K. After looking at the board to figure out what had happened, I eventually realised that there was (past tense here) a tiny little trace between pin 9 on the 68K and the pullup resistor right next to it. Looks like I managed to break that when removing the old pullup.

So, a quick replacement for said trace on the underside...

IMG_20200728_195250.jpg
IMG_20200728_195250.jpg (98.79 KiB) Viewed 3538 times

Boot it up...

IMG_20200728_195754.jpg
IMG_20200728_195754.jpg (140.22 KiB) Viewed 3538 times

And back in business with a correct mono display. :dualthumbup:
User avatar
exxos
Site Admin
Site Admin
Posts: 23498
Joined: Wed Aug 16, 2017 11:19 pm
Location: UK
Contact:

Re: My summer project: A colour Stacy

Post by exxos »

:bravo: :goodpost:
https://www.exxosforum.co.uk/atari/ All my hardware guides - mods - games - STOS
https://www.exxosforum.co.uk/atari/store2/ - All my hardware mods for sale - Please help support by making a purchase.
viewtopic.php?f=17&t=1585 Have you done the Mandatory Fixes ?
Just because a lot of people agree on something, doesn't make it a fact. ~exxos ~
People should find solutions to problems, not find problems with solutions.
atari030
Posts: 315
Joined: Mon Feb 12, 2018 12:43 pm

Re: My summer project: A colour Stacy

Post by atari030 »

Threads like this are gold, nice work.
User avatar
derkom
Moderator
Moderator
Posts: 1208
Joined: Sun Jul 29, 2018 6:45 pm

Re: My summer project: A colour Stacy

Post by derkom »

atari030 wrote: Wed Jul 29, 2020 12:55 am Threads like this are gold, nice work.
:thanksblue:

IMG_20200729_075314.jpg
IMG_20200729_075314.jpg (61.22 KiB) Viewed 3504 times

Looks like bus loading was indeed the issue with the relocator card last week, as GEMBench has now made it all night with the relocator installed (with just 68HC000 in one socket for now).
User avatar
derkom
Moderator
Moderator
Posts: 1208
Joined: Sun Jul 29, 2018 6:45 pm

Re: My summer project: A colour Stacy

Post by derkom »

And here's the relocator board with both the R1C TOS206/IDE board and the 68HC000 installed...

IMG_20200729_085954.jpg
IMG_20200729_085954.jpg (167.2 KiB) Viewed 3497 times

This is not how I plan to provide TOS 2.06 in the end, but this board is easier to install than the Cloudy.

One GEMBench run (not expecting any performance boost at this point of course)...

IMG_20200729_091758.jpg
IMG_20200729_091758.jpg (128.9 KiB) Viewed 3497 times
User avatar
derkom
Moderator
Moderator
Posts: 1208
Joined: Sun Jul 29, 2018 6:45 pm

Re: My summer project: A colour Stacy

Post by derkom »

While I was composing the last post, with the Stacy just sitting at the GEMBench main screen, it spontaneously rebooted. Insufficient power on the bus? Maybe my relocator needs decoupling caps?
User avatar
PhilC
Moderator
Moderator
Posts: 6016
Joined: Fri Mar 23, 2018 8:22 pm

Re: My summer project: A colour Stacy

Post by PhilC »

derkom wrote: Wed Jul 29, 2020 7:27 am While I was composing the last post, with the Stacy just sitting at the GEMBench main screen, it spontaneously rebooted. Insufficient power on the bus? Maybe my relocator needs decoupling caps?
That relocator looks good. Pop a 100uf cap on the board and hopefully that'll help. Of course other problems can be the dreaded socket and pin combo.
If it ain't broke, test it to Destruction.
User avatar
derkom
Moderator
Moderator
Posts: 1208
Joined: Sun Jul 29, 2018 6:45 pm

Re: My summer project: A colour Stacy

Post by derkom »

PhilC wrote: Wed Jul 29, 2020 8:50 am That relocator looks good. Pop a 100uf cap on the board and hopefully that'll help. Of course other problems can be the dreaded socket and pin combo.
Yeah I'll do that at least for good measure, once it crashes again. Actually it's been solid ever since that reboot (knock on something), but regardless, a cap won't hurt. I didn't bother incorporating that into the board design because I knew it wouldn't be the final design, and it's trivial to add externally for testing.

The sockets are good quality turned pin sockets. The pins I'm using are just something from eBay, but they've performed well in the past, and seem fairly good, so hopefully they play well together. Due to vertical space limitations, the final build here is expected to eliminate the sockets on the top of the relocator (direct soldering the boards), but the socket and pin combo will still exist for the motherboard connection.

Edit: Is there such a thing as too many decoupling caps? The eventual build here will have boards in both sides that have their own decoupling caps. Is it a bad thing to have them both on my relocator and on the board connected to it?
User avatar
exxos
Site Admin
Site Admin
Posts: 23498
Joined: Wed Aug 16, 2017 11:19 pm
Location: UK
Contact:

Re: My summer project: A colour Stacy

Post by exxos »

More caps the better ;)
https://www.exxosforum.co.uk/atari/ All my hardware guides - mods - games - STOS
https://www.exxosforum.co.uk/atari/store2/ - All my hardware mods for sale - Please help support by making a purchase.
viewtopic.php?f=17&t=1585 Have you done the Mandatory Fixes ?
Just because a lot of people agree on something, doesn't make it a fact. ~exxos ~
People should find solutions to problems, not find problems with solutions.
User avatar
JezC
Posts: 2081
Joined: Mon Aug 28, 2017 11:44 pm

Re: My summer project: A colour Stacy

Post by JezC »

Only issue I've seen with more and more caps can be the inrush current when all are fully discharged; that might increase the loading on the PSU start-up.

Shouldn't be a big issue with a refurbished PSU though.
Post Reply

Return to “HARDWARE DISCUSSIONS”