3D Printed CT60e Bracket

The place to discuss & share your 3D models or printable parts!
Post Reply
derkom
Posts: 181
Joined: Sun Jul 29, 2018 6:45 pm

3D Printed CT60e Bracket

Post by derkom » Wed Sep 04, 2019 3:19 pm

I've built a power/power button/060 toggle switch bracket for the CT60e, which you can find on Thingiverse or fully editable on Tinkercad.

The text I've written on Thingiverse...

---
This is a bracket for an Atari Falcon030 computer with the CT60e 68060 accelerator card and a picoPSU power supply. It sits under the CT60e and slots into the PSU slots on the motherboard, and fills the empty IEC inlet and power switch holes on the back on the Falcon case.

In the former IEC inlet space are now holes for the picoPSU +12V input, a CT60e power button, and a 68030/68060 toggle switch. The former power switch space is left available for future expansion.

The +12V input hole (the lowest of the three) should work for any picoPSU (and perhaps for similar tiny ATX power supplies if they use the same size input), but the other two holes may require customisation to fit your own power button and switch. A fully customisable version can be found on Tinkercad.

I found this prints best with the "back" (i.e. the part that shows outside the back of the Falcon once installed) facing down on the build plate. I got best results printing on blue tape with no raft. Since this orientation results in the vertical (post-installation) holes being filled with support material, after pulling the supports out with pliers, I smoothed out the insides with a 7 mm drill bit turned by hand. If these holes aren't fairly clean inside, it will be difficult to get the Falcon top case back on.
---

Feel free to download, customise, improve, and enjoy!

IMG_20190904_100617.jpg
IMG_20190904_100617.jpg (50.37 KiB) Viewed 616 times
IMG_20190904_100713.jpg
IMG_20190904_100713.jpg (61.45 KiB) Viewed 616 times
IMG_20190904_095056.jpg
IMG_20190904_095056.jpg (133.94 KiB) Viewed 616 times
IMG_20190904_121040.jpg
IMG_20190904_121040.jpg (200.87 KiB) Viewed 616 times
IMG_20190904_121822.jpg
IMG_20190904_121822.jpg (179.82 KiB) Viewed 616 times
IMG_20190904_153610.jpg
IMG_20190904_153610.jpg (127.22 KiB) Viewed 616 times

troed
Moderator
Moderator
Posts: 507
Joined: Mon Aug 21, 2017 10:27 pm

Re: 3D Printed CT60e Bracket

Post by troed » Wed Sep 04, 2019 6:33 pm

Thanks! Looks good.

User avatar
Icky
Moderator
Moderator
Posts: 1576
Joined: Sun Sep 03, 2017 10:57 am
Location: UK

Re: 3D Printed CT60e Bracket

Post by Icky » Wed Sep 04, 2019 9:45 pm

Nice :). Great seeing all these different designs coming out for the Atari computers.

User avatar
TheNameOfTheGame
Posts: 27
Joined: Tue Dec 05, 2017 5:49 pm
Location: Almost Heaven, West Virginia

Re: 3D Printed CT60e Bracket

Post by TheNameOfTheGame » Thu Sep 05, 2019 12:19 pm

Yes, good design. I wonder if there is an Atari Grey color?

derkom
Posts: 181
Joined: Sun Jul 29, 2018 6:45 pm

Re: 3D Printed CT60e Bracket

Post by derkom » Thu Sep 05, 2019 1:35 pm

TheNameOfTheGame wrote:
Thu Sep 05, 2019 12:19 pm
I wonder if there is an Atari Grey color?
I ran out of two better colours while iterating on the design. :lol: Ended up with the only non-silly colours left being black and white, and I went with white because it would photograph better.

When I reorder filament, I do plan to see if my local supplier has something closer to the Falcon case colour, but of course since the visible parts are in the back, it's not terribly important.

derkom
Posts: 181
Joined: Sun Jul 29, 2018 6:45 pm

Re: 3D Printed CT60e Bracket

Post by derkom » Thu Sep 12, 2019 4:34 pm

For anyone who was planning on printing this bracket, note that I have uploaded a slightly improved design. The Thingiverse link in the first post is still correct, but the Tinkercad link for the editable version of the design has changed, and it is now here.

I had my factory PSU back in the Falcon yesterday and I realised that the legs from the Falcon top case rest on top of the feet of the PSU, so my design, which allowed the legs to pass all the way through and rest on the motherboard allowed the case legs to sit 1 mm too low and also missed an opportunity for the legs and the case screw to hold the bracket in place. This is fixed in the new version. This should also improve the bracket's usability for anyone with an older CT60 or CT63, since it no longer relies on the CT60e card to provide any stability for the bracket.

Post Reply

Return to “3D MODELS”